Skip to main content

How to Make a Lego Table out of Wood

I am an accountant by trade, but I love to spend my free time in my workshop building different things.

Lego table

Lego table

How to Build a Lego Table

Legos are one of the best toys around. They are easy to use and help to develop creativity in kids because they can build anything that they can imagine. My kids love them and play with them for hours at a time. One of the worst things about Legos, however, is that they are small and can be very painful to step on in a dark room.

We looked at different kinds of Lego tables but decided to build our own. You may be thinking that you have no idea how to build your own table, but with these easy-to-follow plans, anyone can do it.

Decisions to Make Before You Build Your Lego Table

Several decisions must be made before building a Lego table.

  • Plates: The biggest factor to consider is that base Lego plates are 10” x 10” squares. Lego plates can be cut using a fine blade on a table saw, or a circular saw, but depending on your saws skills, it may be easier to plan to use whole plates. I chose to use eight plates on the one that I built in a 4x2 pattern.
  • Paint or Stain: In addition, it is a good idea to decide whether you are going to paint or stain the table when you are finished. If you choose to paint it, you may decide to you use plywood or MBF for the sides.

Lego Table Supply List

The plans in the picture above use the dimensions of the Lego table that I built. If you choose to use a different number of Lego plates, they will have to be adjusted accordingly.

  • (1) 24” x 48” x ½” Plywood or MBF
  • (4) 1” x 6” x 8’
  • (3) 1” x 10” x 8’
  • (3) 1” x 4” x 8’
  • (2) Pine case molding⁠—need better description
  • (8) Lego Plates (10 x 10)⁠—the color of your choosing
  • (2) ¾” wide x ¼” thick Straight Trim
  • (1) Can paint or stain
  • (1) Can high-gloss polyurethane
  • (1) Tube of wood putty
  • (1) Bottle of wood glue
  • (2) Tubes of epoxy⁠—better description
  • (1) Box 1 ¼ wood screws

Tools Needed

The following is a list of tools that are recommended:

  • Table saw
  • Miter saw
  • Cordless drill
  • Air compressor with nail gun
  • Bar clamps
  • Right-angle clamps

Building Your Own Lego Table

The instructions below are broken into three main groups of parts and assembly: storage shelves, tabletop, and trim. Each section will have cutting instructions as well as assembly instructions.

Storage shelf plans

Storage shelf plans

Storage Shelf Cut List

We will start with building the storage shelves first since they will serve as the legs for the table. Remember that 1x4s, 1x6s, and 1x10s measure differently than you think. For one, all of those boards are only ¾” thick and not a full inch as the name says. In addition, all of the boards commonly measure a ½” short of what they actually say. For example, a 1x4 is actually ¾” x 3 ½”.

  1. Using the table saw, rip two 1x4s in half so that they are about 1 ½” wide. Do not worry if you are a little off one way or the other. This will create your shelf rail.
  2. Take those four boards over to the miter saw, cut them into twelve 22” boards, and set them aside. It is critical that these boards be very close in length.
  3. Take the 1x6s over to the miter saw and cut sixteen of them to 22”. Be sure to be accurate with your cuts.
  4. While at the miter saw, take two of the 1x10s, and cut eight of them to 22”.

Storage Shelf Assembly Instructions

It is very important to take your time when assembling the storage shelves. Assembly itself will not take that much time.

  1. Select four 1x6s and lay them next to each other. Play with them to see how they will fit together. Once you are satisfied with how they fit, measure up 5 ¼” from the bottom on the far right board and make a mark. Draw a straight line across the board using a square.
  2. Take one of the 1x4s that have been ripped down to 1 ½” and place it just above the line. Drill a pilot hole on the far right-hand side. Using 1 ¼” screws, drive one screw into the shelf rail to secure it. Measure down ¾” from the top of the 1x6 and draw a line. Grab another shelf rail, drill a pilot hole in it, and secure it right under the line at the top with one screw.
  3. On the next 1x6, run a bead of glue down the edge of the board and slide the board next to the first 1x6. Be sure that the tops and bottoms match up. Measure up 5 ¼” and draw a line. Make sure that the bottom shelf rail runs across the second 1x6 just above the line as the first one does. Drill another pilot hole in the shelf rail and secure it to the second board. Measure down ¾” from the top and draw a line on the second 1x6. Drill a pilot hole and use a screw to secure it. Repeat this step until all four boards have been attached. It is a good idea to go back and add a second screw to each 1x6. Go back and add a third rail that is 4 ½” higher than the top of the bottom rail.
  4. Clean off any excess glue with toweling or an old rag.
  5. Set this one aside and assemble the other three using the same instructions.
  6. Sand the front and back of each side. Try to make sure that where the 1x6s come together is smooth.
  7. Grab two 1x10s. Put a bead of glue on the edge of one of them. Take the other one and stand it on its side. Take one of the sides and line up the top, the side with the shelf rail that is ¾” down from the top, with the 1x10 that has the glue on it. The other 1x10 will support the bottom of the side. Make sure that the 1x10 with glue on it is flush with the side on each end. Take the right-angle clamps and place one on each side of the top. Use the nail gun to nail the 1x10 in place. Let it sit for a few minutes to allow the glue to set. Remove the right-angle clamps. Grab another 1x10 and run a bead of glue down the edge. Align the 1x10 with the bottom of the side and secure it with the right angle clamps. Make sure that the 1x10 is flush with the bottom and edges of the side. Use the nail gun to secure the bottom shelf in place. Repeat the same procedures to attach the middle shelves.
  8. Carefully flip over the side with the shelves attached. Run beads of glue down the end of the shelves. Take another side and lay it over the top. Hold or clamp each in place and secure with the nail gun. Make sure all of the edges are flush.
  9. Carefully set the storage shelf aside and repeat the instructions to build the second storage shelf.
Table top plans

Table top plans

Tabletop Cut List

Now that the two storage shelves have been built, it is time to turn our attention to the tabletop. Using the table saw, rip the 2’x4’ sheet of plywood to a width of 44 ¼”. It is critical to cut as straight as possible. There will be trim that covers the edge, but if you are off too much, you will be able to see the discrepancy in how the face trim lines up with the top trim.

Tabletop Assembly

Now it is time to attach the top of the table to the storage shelves.

  1. Spread the storage shelves apart until they are about the length of the top apart. Place the tabletop on top of the storage shelves. Align the storage shelves so that they are flush with the edge of the table. There should be an inch on both sides of the long side of the tabletop. Take your time and make sure that both sides are right. With the cordless drill, drill a few pilot holes through the tabletop and into the storage shelves without going all the way through. Drive twelve screws into the tabletop on each side. Make sure the heads of the screws are as flat as possible. You can even slightly countersink them; however, do not drive them through the top shelf.
  2. Take the Lego plates and arrange them in a 4x2 pattern on the top of the table. Center them in the middle. Using a pencil, draw a line around the outside of the plates to mark where they should go. One by one, put epoxy on the back of the plates and set them into place. Once you have them all set, put heavy objects on top of them, and let them dry for an hour or two.
Plans for finishing touches

Plans for finishing touches

Finishing Touches

Now that the Lego table is assembled, it is time to add trim and either paint or stain it. When it comes to cutting the trim, use the measurements that I provide below as a guide and not as gospel. If there are slight variances between my cuts and yours, the trim will be off and not look right. Cut the trim in the order that I list and remember the old adage, measure twice, and cut once.

  1. Face Trim: Take the ¾” straight trim and cut two pieces to 24” and two other pieces to 44 5/8”. Put a bead of glue on the back of one of the short pieces and hold it against the side of the tabletop to cover the side of the plywood. Make sure it is flush with the top and nail-gun it in place. Take one of the long pieces and use it to cover the end of the other piece of trim, and it should slightly overhang the other side. Next, take the other 24” piece, and after applying glue to the back, nail it into place using the nail gun. Take the final piece, put glue on the back, and nail it into place. The key to remember here is to make sure that the molding is flush with the top and sides of the plywood.
  2. Top Trim: Grab the pine case molding and cut a 45o angle from the end of the skinnier end to where ever it ends on the fatter side. From the skinnier side of the molding, measure 24 ½” and make a mark on the skinnier side. Cut a 45o angle in the other direction that ends at the mark. When you are done, the skinny side should be longer at both ends. Position it on the table, but do not nail it in yet. Measure the distance from the outside on the piece that you already cut down the long side of the table and figure out the overhang that will match up to the next piece of trim. The length of my table was 44 5/8” from the outside of the first piece to the long side of the next end. Put that piece on the table and repeat the same process for the other two pieces. Remember to measure each piece and not just go with my measurements. The trim should butt up against the Lego plates. A great tip here is to cut the trim a little long and adjust it after you cut the other pieces. Once all of the pieces are ready, put a bead of glue on the back of one and nail it into place using the nail gun. Use a 5/8” nail in the nail gun so that you do not shoot through the top.
  3. Storage Trim: Measure the distance from the top of the storage shelf to the bottom for each of the sides of the storage shelves (8 measurements). Rip the remaining 1x4 into two strips that are 1 ½” wide. Cut those to length and attach them to the Lego table using glue and the nail gun using 1 ¼” nails. Measure the distance in between the vertical trim that you just put on and rip the remaining 1x10 to that width. In my case, it was 8 ½”. One thing to think about here is that you may have to cut this a little wide and trim it up if your gap is not the same all the way around. Using the miter saw, cut sixteen ¾” pieces. Put a bead of glue on the piece and nail gun it to each of the shelf faces.
  4. Paint/Stain: Cover the Lego plates well and either paint or stain your table. I choose to stain mine. I also put on a high gloss polyurethane finish to protect it from wear and tear.

Good Luck!

The best advice that I can give you is to read the plans several times before doing anything. The second is to measure twice and cut once. It took me a few days to build this table from start to finish. Another great idea is to buy Tupperware containers that fit into the shelves to store your Legos.

© 2012 Eric Cramer


Lorelei Cohen from Canada on June 08, 2020:

If only I could be so handy in the workshop! Beautiful job, I love the many nooks and crannies for storage. FYI: I still love to play with Legos.

Chris hoffman on November 04, 2015:

Lego plates (all Legos actually) are made from ABS plastic, as are plastic shower surround materials. Buy a caulk tube of shower surround adhesive (I have used loctite power grab from Home Depot $5). Some of the more powerful construction adhesives are known to actually burn through ABS shower surround material, so I'd stick with one meant for shower surrounds. Scuff the back of the lego plates with some sandpaper and apply the adhesive with a fine notched trowel and slap it on your wood ;) Gently press any lumps out. To date I've made 4 lego tables like this and it works wonderfully.

Kristen Howe from Northeast Ohio on April 04, 2015:

How cool is that! I love that idea, Eric. Very crafty, clever and fun! Voted up for awesome!

Anastasia Bronnikova from Russia, Novosibirsk on February 13, 2015:

Whoa, that's brilliant! Instantly added to my list of dream furniture.

Candice Watts from Myrtle Beach, South Carolina on November 12, 2014:

This is WONDERFUL! My boyfriend's son loves Lego's almost more than he loves mine craft! I am definitely going to have to use this!!

Treasures By Brenda from Canada on August 21, 2014:

Wow! Brilliant idea. My boys would have loved this!

LEGOdomenick on June 12, 2014:

This is great. I am going to have to come back to this when my kids are older.

Sarah Forester from Australia on April 04, 2014:

I wish I was this handy.

Amy D. from Mostly in My Own Little World on November 11, 2012:

Awesome. This would look so good under the tree for my little girl this year. Great hub, voted up and useful.

Eric Cramer (author) from Chicagoland on September 07, 2012:

Thanks! It should make a great desk.

MargaritaEden from Oregon on September 07, 2012:

This is such a great idea, I love that table, I want one for my kids to do homework on, I really like the many shelves. I think I will use your idea, I guess I can skip on the lego plate on top and just go with regular table top. Wonderful hub!

TLMinut on August 21, 2012:

I had a toy table for my boys and tried just gluing the base plates on - it didn't really work. Okay, it didn't work at all. I always wanted to have one for them. Maybe I'll make one for THEIR kids now!

Marites Mabugat-Simbajon from Toronto, Ontario on August 19, 2012:

Very useful and interesting for a friend who has two little boys and crazy about Lego! Great craft to share!

RTalloni on August 19, 2012:

A super project here in a well done hub. Congrats on your Hub of the Day award!

DreamerMeg from Northern Ireland on August 19, 2012:

That's a great idea. Something to think about!

emimemo from USA on August 19, 2012:

It is a great lego table. I can't say eveybody can make the table which looks like what you made, but it is very nice hub. Thank you for sharing. You are very talented.

cfin from The World we live in on August 19, 2012:

So original, well written and appealing to our inner lego lover.

Thanks, voted up.

Susan Keeping from Kitchener, Ontario on August 19, 2012:

What a great idea, wish I'd had one when I was a kid

Craig Hartranft from Southeastern Pennsylvania on August 19, 2012:

Very attractive and useful. We created something similar for the Thomas the Tank Engine wooden train stuff but at coffee level height.

Your Cousins from Atlanta, GA on August 19, 2012:

I can't build it, but I sure could play on it. Great piece of handiwork and what a nice idea to get the kids to engage in creative playtime. Voted Up!

Adam Hughes from Chicagoland, IL on August 19, 2012:

You know what's funny? I'm sitting here looking at the picture of this table, and I see the note that says Ryan and AJ on it, and thought, wow, those are the names of (your wife's) kids. And I'm all, wait... and I look and see it is in fact Eric Cramer that wrote this Hub. I saw the picture and it scrolled through to the next Hub and I arrowed back to look at the table again, thinking I'd like to make one of those when I saw the kids' names. Kinda funny... at least in my head.

Adam Hughes

Stephanie Bradberry from New Jersey on August 19, 2012:

This is a great idea. I have seen desk/tables with somewhat similar tops at my kids' playschool, but none have the side shelves, and of course they do not come with directions for making them.

These plans would give us a good reason to put the woodshop back in action.

editsvcs on August 19, 2012:

This is beautiful and so practical! We turned the tabletop of an unused train table into a Lego table in much the same way. I like how your table has the storage already built in and two chairs can fit underneath.

Rebecca Mealey from Northeastern Georgia, USA on August 19, 2012:

Great for those that have some building knowledge. I'm afraid I wouldn't be any good at it. Neat idea!

Sophie from United Kingdom on August 19, 2012:

This is incredible!

I wish I had a huge table like this when I was a kid!

I guess you should patent this table, before some great company steals your idea! You should be a millionaire, and I wish you that! :)

Thanks a lot for sharing, voted up + useful/awesome!

nishlaverz from N.E England on August 19, 2012:

I would have to build one with my old road and grass board set. Create a Lego City Board. I say I but really mean my partner who is a joiner. My daughter loves lego and has pinched all of my old stuff and has loads of her own.

Linda Chechar from Arizona on August 17, 2012:

What a great idea and instructional Hub! Well done! I didn't have Legos as a kid, but did play with Lincoln Logs. :)

Riverfish24 from United States on August 07, 2012:

Wow, this is a great and innovative hub! Nice work.

Eric Cramer (author) from Chicagoland on August 07, 2012:

My kids are constantly building their Lego creations on it. My oldest also uses the table to build card houses.

jsasson from Florida on August 07, 2012:

You could build some serious Lego with a rig like that